Determination of the hygroexpansion properties of wood-based composite panels
DOI:
https://doi.org/10.37636/recit.v7n3e348Keywords:
Pinus pseudostrobus, Plywood, Stripboard, Medium density board, Oriented strand boardAbstract
Wood panels expand when exposed to moisture in service conditions. Consequently, their performance as an engineering material is impoverished and results in repair and/or replacement costs. The objective of the research was to determine the densities and hygroexpansions of plywood, strandboard, medium density and oriented strandboard. The same parameters were evaluated on a control group of Pinus pseudostrobus solid wood. Thirty-five randomly selected specimens were prepared from each material. Hygroscopy tests were performed with a protocol of humidification and drying of the experimental material. The hygroexpansions of plywood, strandboard, medium density and oriented strandboard are different compared to the hygroexpansion of P. pseudostrobus solid wood. Wood and wood-based panels exhibit hygroscopic character, which results in dimensional variation if their moisture content is changed. The magnitudes of the hygroexpansions of the four boards studied are greater than that of solid wood of P. pseudostrobus.
Downloads
References
P. Bekhta, O. Chernetskyi, I. Kusniak, N. Bekhta, and O. Bryn, “Selected Properties of Plywood Bonded with Low-Density Polyethylene Film from Different Wood Species”, Polymers, vol. 14, p. 51, 2022. https://doi.org/10.3390/polym14010051 DOI: https://doi.org/10.3390/polym14010051
D. Kocaefe, X. Huang, and Y. Kocaefe, “Dimensional Stabilization of Wood”, Current Forestry Reports, vol. 1, pp. 151-161, 2015. https://doi.org/10.1007/s40725-015-0017-5 DOI: https://doi.org/10.1007/s40725-015-0017-5
R. Sargent, “Evaluating dimensional stability in solid wood: a review of current practice”, Journal of Wood Science, vol. 65, no. 36, pp. 1-11, 2019. https://doi.org/10.1186/s10086-019-1817-1 DOI: https://doi.org/10.1186/s10086-019-1817-1
J. R. Sotomayor Castellanos, E. Hernández Corona, M. Pérez López, and D. Soto Rangel, “Caracterización mecánica de madera reconstituida. Tableros aglomerados, contrachapados y enlistonados de madera. Higro-contracción e higro-expansión,” Investigación e Ingeniería de la Madera, vol. 8, no. 1, pp. 3-22, 2012. https://www.researchgate.net/publication/261064508_Caracterizacion_mecanica_de_madera_reconstituida_Tableros_aglomerados_contrachapados_y_enlistonados_de_madera_Higro-contraccion_e_higro-expansion_Tratamiento_higro-termico_y_pruebas_de_ultrasonido_en_
A. Patera, D. Derome, M. Griffa, and J. Carmeliet, “Hysteresis in swelling and in sorption of wood tissue”, Journal of Structural Biology, vol. 182, no. 3, pp. 226-234, 2013. https://doi.org/10.1016/j.jsb.2013.03.003 DOI: https://doi.org/10.1016/j.jsb.2013.03.003
E. T. Engelund, L. G. Thygesen, S. Svensson, and C. A. S. Hill, “A critical discussion of the physics of wood-water interactions”, Wood Science and Technology, vol. 47, no. 1, pp. 141-161, Jan. 2013. https://doi.org/10.1007/s00226-012-0514-7 DOI: https://doi.org/10.1007/s00226-012-0514-7
M. Nopens, M. Riegler, C. Hansmann, and A. Krause, “Simultaneous change of wood mass and dimension caused by moisture dynamics”, Scientific Reports, vol. 9, no. 10309, pp. 1-11, 2019. https://doi.org/10.1038/s41598-019-46381-8 DOI: https://doi.org/10.1038/s41598-019-46381-8
D. Derome, C. Zhang, M. Chen, and J. Carmeliet, “Understanding swelling of wood through multiscale modeling,” in 7th International Building Physics Conference, IBPC2018, Syracuse, 2018, pp. 355-360. https://doi.org/10.14305/ibpc.2018.be-9.06 DOI: https://doi.org/10.14305/ibpc.2018.be-9.06
R. C. Neagu, E. K. Gamstedt, and M. Lindström, “Influence of wood–fibre hygroexpansion on the dimensional instability of fibre mats and composites”, Composites Part A, Applied Science and Manufacturing, vol. 36, no. 6, pp. 772-788, 2005. https://doi.org/10.1016/j.compositesa.2004.10.023 DOI: https://doi.org/10.1016/j.compositesa.2004.10.023
T. Gereke, P. Hass, and P. Niemz, “Moisture-induced stresses and distortions in spruce crosslaminates and composite laminates”, Holzforschung, vol. 64, no. 1, pp. 127-133, 2010. https://doi.org/10.3929/ethz-b-000017324 DOI: https://doi.org/10.1515/hf.2010.003
G. C. Ajuziogu, A. N. Amujiri, E. U. Njoku, C. B. Ozokolie, and E. O. Ojua, “Determination of swelling and dimensional stability of some Nigerian timber species”, Annual Research & Review in Biology, vol. 35, no. 1, pp. 24-29, 2020. https://doi.org/10.9734/ARRB/2020/v35i130177 DOI: https://doi.org/10.9734/arrb/2020/v35i130177
M. Böhm, K. Kobetičová, J. Procházka, and R. Černý, “Moisture sorption and thickness swelling of wood-based materials intended for structural use in humid conditions and bonded with melamine resin,” en IOP Conference Series. Materials Science and Engineering, vol. 549, no. 1, pp. 1-9, 2019. https://doi.org/10.1088/1757-899X/549/1/012042 DOI: https://doi.org/10.1088/1757-899X/549/1/012042
A. Holstovs, G. Farmer, and B. Bridgens, “Sustainable Materialization of Responsive Architecture”, Sustainability, vol. 9, no. 3, pp. 435, 2017. https://doi.org/10.3390/su9030435 DOI: https://doi.org/10.3390/su9030435
D. Correa, O. D. Krieg, A. Menges, R. Reichert, and K. Rinderspacher, “Hygroskin: A Climate-Responsive Prototype Project Based on the Elastic and Hygroscopic Properties of Wood,” In ACADIA 13: Adaptive Architecture. Proceedings of the 33rd Annual Conference of the Association for Computer Aided Design in Architecture, Cambridge, pp. 33-42, 2013. https://papers.cumincad.org/data/works/att/acadia13_033.content.pdf
I. De Windt, W. Li, J. Van den Bulcke, and J. Van Acker, “Classification of uncoated plywood based on moisture dynamics”, Construction and Building Materials, vol. 158, pp. 814-822, 2018. https://doi.org/10.1016/j.conbuildmat.2017.09.194 DOI: https://doi.org/10.1016/j.conbuildmat.2017.09.194
M. Sooru, K. Kasepuu, R. Kask, and H. Lille, “Impact of Wetting/Oven-Drying Cycles on the Mechanical and Physical Properties of Birch Plywood”, IOP Conferences Series: Materials Science and Engineering, vol. 96, no. 012075, 2015. https://doi.org/10.1088/1757-899X/96/1/012075 DOI: https://doi.org/10.1088/1757-899X/96/1/012075
J. R. Sotomayor Castellanos, I. Macedo Alquicira, and E. Mendoza González, “Higroexpansión, higrocontracción y sus relaciones de anisotropía de ocho maderas mexicanas”, Tecnociencia Chihuahua, vol. 16, no. 1, e 869, 2022. https://doi.org/10.54167/tecnociencia.v16i1.869 DOI: https://doi.org/10.54167/tecnociencia.v16i1.869
J. R. Sotomayor Castellanos, L. E. A. Ávila Calderón, and M. Fuentes Salinas, “Características higroscópicas de las maderas Spathodea campanulata, Fraxinus americana y Albizia plurijuga impregnadas con boro”, Ciencia UNEMI, vol. 14, no. 35, pp. 10-25, 2021. https://doi.org/10.29076/issn.2528-7737vol14iss35.2021pp10-25p DOI: https://doi.org/10.29076/issn.2528-7737vol14iss35.2021pp10-25p
J. R. Sotomayor Castellanos, I. Macedo Alquicira, and E. Mendoza González, “Características higroscópicas de ocho maderas mexicanas”, Ingenierías, vol. 24, no. 91, pp. 49-63, 2021. https://doi.org/10.29105/ingenierias24.91-22 DOI: https://doi.org/10.29105/ingenierias24.91-22
A. A. Chiniforush, A. Akbarnezhad, H. Valipour, and S. Malekmohammadi, “Moisture and temperature induced swelling/shrinkage of softwood and hardwood glulam and LVL: An experimental study”, Construction and Building Materials, vol. 207, pp. 70-83, 2019. https://doi.org/10.1016/j.conbuildmat.2019.02.114 DOI: https://doi.org/10.1016/j.conbuildmat.2019.02.114
S. Koman, and S. Feher, “Basic density of hardwoods depending on age and site”, Wood Research, vol. 60, no. 6, pp. 907-912, 2015. http://www.centrumdp.sk/wr/201506/07.pdf
Z. Fu, Y. Zhou, X. Gao, H. Liu, and F. Zhou, “Changes of water related properties in radiata pine wood due to heat treatment”, Construction and Building Materials, vol. 227, no. 116692, 2019. https://doi.org/10.1016/j.conbuildmat.2019.116692 DOI: https://doi.org/10.1016/j.conbuildmat.2019.116692
J. R. Sotomayor Castellanos, L. J. García Mariscal, C. E. Moya Lara, and J. B. Olguín Cerón, “Higroscopía y anisotropía de la madera de Pinus michoacana, Pinus douglasiana y Pinus pringlei. Higrocontracción, velocidad del ultrasonido y módulo de elasticidad dinámico”, Investigación e Ingeniería de la Madera, vol. 6, no. 3, pp. 3-32, 2010. https://www.researchgate.net/publication/261099839_Higroscopia_y_anisotropia_de_la_madera_de_Pinus_michoacana_Pinus_douglasiana_y_Pinus_pringlei_Higrocontraccion_velocidad_del_ultrasonido_y_modulo_de_elasticidad_dinamico
C. Lanvermann, F. K. Wittel, and P. Niemz, “Full-field moisture induced deformation in Norway spruce: intra-ring variation of transverse swelling”, European Journal of Wood and Wood Products, vol. 72, pp. 43-52, 2014. https://doi.org/10.1007/s00107-013-0746-8 DOI: https://doi.org/10.1007/s00107-013-0746-8
R. Hajihassani, B. Mohebby, S. K. Najafi, and P. Navi, “Influence of combined hygro-thermomechanical treatment on technical characteristics of poplar wood”, Maderas. Ciencia y tecnología, vol. 20, no. 1, pp. 117-128, 2018. https://doi.org/10.4067/S0718-221X2018005011001 DOI: https://doi.org/10.4067/S0718-221X2018005011001
M. R. T. Esfandiyari, M. T. Pour, H. Khademieslam, S. A. M. Shokraei, and B. Bazyar, “Investigating the Possibility of Making Lignin-glyoxal Resins as Adhesives in the Production of Plywood”, Bioresources, vol. 14, no. 3, pp. 7122-7133, 2019. https://doi.org/10.15376/biores.14.3.7122-7133 DOI: https://doi.org/10.15376/biores.14.3.7122-7133
A. Shalbafan, A. Nadali, and H. Thoemen, “A Multifunctional Mineral Binder for Plywood Production: The Effect of Manufacturing Parameters on Bonding Quality”, Materials, vol. 13, 2360, 2020. https://doi.org/10.3390/ma13102360 DOI: https://doi.org/10.3390/ma13102360
American Society for Testing and Materials, Annual Book of ASTM Standards. Section Four; Construction, Volume 04.10, Wood. West Conshohocken, ASTM, 2009. https://www.astm.org/
M. F. Galikhanov, P. A. Platonova, and A. F. Zamilova, “Influence of Polarization of Urea-Formaldehyde Glue in the Process of Manufacture of Plywood on Its Water and Moisture Absorption”, Polymer Science, Series D, vol. 11, pp. 122-126, 2018. https://doi.org/10.1134/S1995421218020065 DOI: https://doi.org/10.1134/S1995421218020065
A. Lunguleasa, N. Ayrilmis, C. Spirchez, and F. Özdemir, “Investigation of the Effects of Heat Treatment Applied to Beech Plywood”, Drvna industrija, vol. 69, no. 4, pp. 349-355, 2018. https://doi.org/10.5552/drind.2018.1768 DOI: https://doi.org/10.5552/drind.2018.1768
F. Muñoz, and R. Moya, “Effect of nanoclay-treated UF resin on the physical and mechanical properties of plywood manufactured with wood from tropical fast growth plantations”, Maderas. Ciencia y tecnología, vol. 20, no. 1, pp. 11-24, 2018. http://dx.doi.org/10.4067/S0718-221X2018005001202 DOI: https://doi.org/10.4067/S0718-221X2018005001202
A. H. S. Reis, D. W. Silva, A. P. Vilela, R. F. Mendes, and L. M. Mendes, “Physical-mechanical Properties of Plywood Produced with Acrocarpus fraxinifolius and Pinus oocarpa”, Floram, vol. 26, no. 4, e20170157, 2019. http://dx.doi.org/10.1590/2179-8087.015717 DOI: https://doi.org/10.1590/2179-8087.015717
E. S. Wibowo, M. A. R. Lubis, and B-D. Park, “Simultaneous Improvement of Formaldehyde Emission and Adhesion of Medium-Density Fiberboard Bonded with Low-Molar Ratio Urea-Formaldehyde Resins Modified with Nanoclay”, Journal of the Korean Wood Science and Technology, vol. 49, no. 5, pp. 453-46, 2021. https://doi.org/10.5658/WOOD.2021.49.5.453 DOI: https://doi.org/10.5658/WOOD.2021.49.5.453
T. Ozyhar, T. Depnering, C. Ridgway, M. Welker, J. Schoelkopf, I. Mayer, and H. Thoemen, “Utilization of inorganic mineral filler material as partial replacement for wood fiber in medium density fiberboard (MDF) and its effect on material properties”, European Journal of Wood and Wood Products, vol. 78, pp. 75-8, 2020. https://doi.org/10.1007/s00107-019-01480-1 DOI: https://doi.org/10.1007/s00107-019-01480-1
A. Gürgen, D. Ustaömer, and S. Yildiz, “Application of Artificial Neural Network to Predict the Effect of Paraffin Addition on Water Absorption and Thickness Swelling of MDF”, Drvna Industrija, vol. 70, no. 3, pp. 247-255, 2019. https://doi.org/10.5552/drvind.2019.1839 DOI: https://doi.org/10.5552/drvind.2019.1839
W. Gul, H. Alrobei, S. R. A. Shah, and A. Khan, A, “Effect of Iron Oxide Nanoparticles on the Physical Properties of Medium Density Fiberboard”, Polymers, vol. 12, no. 2911, 2020. https://doi.org/10.3390/polym12122911 DOI: https://doi.org/10.3390/polym12122911
H. Alabduljabbar, R. Alyousef, W. Gul, S. R. A. Shah, A. Khan, R. Khan, and A. Alaskar, “Effect of Alumina Nano-Particles on Physical and Mechanical Properties of Medium Density Fiberboard”, Materials, vol. 13, no. 18, p. 4207, 2020. https://doi.org/10.3390/ma13184207 DOI: https://doi.org/10.3390/ma13184207
M-K. Hong, M. A. R. Lubis, and B-D. Park, “Effect of Panel Density and Resin Content on Properties of Medium Density Fiberboard”, Journal of the Korean Wood Science and Technology, vol. 45, no. 4, pp. 444-455, 2017. https://doi.org/10.5658/WOOD.2017.45.4.444
O. Zeleniuc, A-E. Dumitrascu, and V. D. Ciobanu, “Properties Evaluation by Thickness and Type of Oriented Strand Boards Manufactured in Continuous Press Line”, BioResourses, vol. 15, no. 3, pp. 5829-5842, 2020. https://doi.org/10.15376/biores.15.1.199-210 DOI: https://doi.org/10.15376/biores.15.3.5829-5842
B. Zhuang, A. Cloutier, and A. Koubaa, “A Physical and Mechanical Properties of Oriented Strand Board Made from Eastern Canadian Softwood Species”, Forests, vol. 13, p. 523, 2022. https://doi.org/10.3390/f13040523 DOI: https://doi.org/10.3390/f13040523
Published
How to Cite
Issue
Section
Categories
License
Copyright (c) 2024 Javier Ramon Sotomayor Castellanos, Isarael Macedo Alquicira
This work is licensed under a Creative Commons Attribution 4.0 International License.
The authors who publish in this journal accept the following conditions:
The authors retain the copyright and assign to the journal the right of the first publication, with the work registered with the Creative Commons Attribution license 4.0, which allows third parties to use what is published as long as they mention the authorship of the work and the first publication in this magazine.
Authors may make other independent and additional contractual agreements for the non-exclusive distribution of the version of the article published in this journal (eg, include it in an institutional repository or publish it in a book) as long as they clearly indicate that the work it was first published in this magazine.
Authors are allowed and encouraged to share their work online (for example: in institutional repositories or personal web pages) before and during the manuscript submission process, as it can lead to productive exchanges, greater and more quick citation of published work (see The Effect of Open Access).
